Products & applications

Every alloy grade, one page

Twelve published FeCrAl and NiCr heating-alloy grades each have their own specification page below, with chemical composition, resistivity by diameter band, Ct temperature factors and ohm-per-metre tables. CuNi1–CuNi44, pure nickel and the manganin / constantan precision alloys are covered on their own series pages. Values shown here are nominal values from our 2026 English datasheets.

FeCrAl resistance alloys (8 grade pages)

Iron-chromium-aluminium heating alloys produced to GB/T 1234-2012. Higher maximum service temperature and lower density than NiCr; select by working temperature, cycling and atmosphere.

NiCr resistance alloys (4 grade pages)

Nickel-chromium heating alloys produced to GB/T 1234-2012. Good ductility after high-temperature service and stable resistance for wound elements.

Other alloy series & product forms

CuNi44 is a copper-nickel resistance grade and is not the same material as constantan / manganin precision resistance alloys; the two families follow different standards and are listed separately.

CuNi resistance wire

CuNi1–CuNi44 (11 grades)

Low-resistance copper-nickel alloys for shunts, heating cables, resistors and connectors.

Pure nickel wire

Ni200 / Ni201 equivalents

Pure nickel wire, rod and strip for electronics, chemical equipment and battery connections.

Standard: GB/T 5235-2021 · GB/T 21653-2008 · GB/T 4435-2010 · GB/T 2072-2020

Precision resistance alloys

Manganin / constantan

Precision resistance wire, sheet and rolled wire with a very low temperature coefficient of resistance.

Standard: GB/T 6145-2010

Strip & ribbon

Form

Rolled strip and ribbon in FeCrAl, NiCr and CuNi grades for high-power elements.

Standard: GB/T 1234-2012

Flat wire

Form

Flat rolled wire for compact heating elements and resistors.

Standard: GB/T 1234-2012

Heating elements

Form

Finished and semi-finished coils, tubes and formed elements to drawing.

Applications

Where our resistance alloys are used

Taken from the application sections of our 2026 English datasheets. The right grade depends on temperature, atmosphere, cycling and the mechanical form of the element — use these as a starting point, then confirm with our engineers.

Industrial heat-treatment furnaces

Periodic / batch furnaces, carburising, bell-type and ammonia-decomposition lines, kilns, dryers and process heating equipment.

Typical grades: Cr20Ni80 · details →

Premium heating tubes & elements

Tubular, coil and ribbon elements where dimensional stability and long service life matter.

Typical grades: Cr20Ni80 / FeCrAl · details →

Domestic & commercial heaters

Radiant, convection and fan heaters, and other appliance heating circuits.

Typical grades: NiCr / FeCrAl · details →

High-temperature resistors

Load, braking and discharge resistor banks that need reproducible resistivity.

Typical grades: Cr20Ni80 · details →

Shunts & current sensing

Low-resistance copper-nickel grades with a tight temperature coefficient; CuNi34 is the zero-TCR grade in our range.

Typical grades: CuNi1–CuNi44 · details →

Heating cables & connectors

Low-resistance CuNi wire for heating cables, brake resistors and high-temperature connectors.

Typical grades: CuNi · details →

We do not publish customer names, case studies or performance claims that we cannot document. If you need a reference for a specific application, tell us the operating conditions and we will discuss what we can substantiate.
Selection support

Give us the conditions, we will check the grade

Working temperature, atmosphere, supply voltage, target power, available space and cycling profile are enough for us to shortlist a grade and a wire or strip size.

Open the selection tool Send the conditions

Cannot find the grade you need?

Tell us the target resistance, size and operating conditions. We will check our full range, including grades not listed here.

WhatsApp